View AP3125HA_8206167.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AP3125HA/hb document number: ds37169 rev . 3 - 2 1 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product green mode pwm controller description the ap3125 h a/ hb is a current mode pwm controller which is optimized for high performance, low standby power and cost effective offline flyback converters. the pwm switching frequency at normal operation is internally fixed (about 100 khz ). in middle load, the ic will enter green mode to improve system efficiency with the help of frequency foldback . a minimum switching frequency (about 20khz ) is set to avoid t he audible noise. in no load or light load, the ic will enter the burst mode to minimize standby power . furthermore, the f requency dithering function is built - in to reduce emi emission. i nternal slope compensation allows more stable peak - c u rrent mode control over wide range of input voltage and load conditions. internal line compensation ensures constant output power limit over entire universal line voltage range. c omprehensive protection f eatures are included, such as cycle - by - cycle current limit (oc p), vcc over voltage protection (vovp), internal otp , o ver l oad p rotection (olp) and pins fault protection. AP3125HA features external otp/ovp by using a minimal number of external components with ctrl pin . ap3125 hb features built - in b rownout (bno) and line over voltage protection (lovp). features ? very low start - up current ? current mode control ? non - audible - noise green - mode control ? internal slope compensation ? soft start during startup process ? frequency fold back for high average efficiency ? secondary winding short protection with focp ? soft switching for reducing emi ? vcc maintain mode ? brownout p rotection (bno , ap3125hb ) ? line over voltage p rotection ( lovp , ap3125hb) ? useful pin fault protection: sense pin floating ctrl pin short to ground (AP3125HA) fb/opto - coupler open/short ? comprehensive system protection feature: vcc over voltage protection (vovp) over load protection (olp) ? e xternal otp/ovp with ctrl pin protection (AP3125HA) ? mini size package of sot26 ? pin to pin compatible with ap3125a/v/r/l/b ? totally lead - free & fully rohs compliant (note s 1 & 2) ? hal ogen and antimony free. green device (note 3) pin assignments ( top view) sot26 (for AP3125HA ) ( top view) sot26 (for ap3125hb ) applications ? switching ac - dc adapter/charger ? atx/btx auxiliary power ? set - top box (stb) power supply ? open frame switching power supply note s: 1 . no purposely added lead. fully eu directive 2002/95/ec (rohs) & 2011/65/eu (rohs 2) compliant. 2. see http://www.diodes.com/quality/lead_free.html for more information about diodes incorporateds definitions of hal ogen - and antimony - free, "green" and lead - f ree . 3. halogen - and antimony - free "green products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total br + cl) and <1000ppm antimony compounds . 1 2 3 4 5 p i n 1 m a r k 6 g n d f b c t r l g a t e v c c s e n s e 1 2 3 4 5 p i n 1 m a r k 6 g n d f b b n o g a t e v c c s e n s e
AP3125HA/hb document number: ds37169 rev . 3 - 2 2 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product typical applications circuit ~ ~ + - v c c g n d g a t e f b s e n s e b n o ~ a z 4 3 1 a p 3 1 2 5 h b l 2 t 1 r 1 3 c 7 c 6 c 8 r 1 4 r 1 5 r 1 6 r 1 7 r 1 8 c 9 c 1 0 r 1 2 r 1 1 r 1 0 r 9 c 5 r 6 r 1 9 c 4 r 5 r 4 c 2 c 1 v r 1 n t c r 2 r 3 f 1 r 7 c 3 c 1 1 r 8 r 2 0 c 2 0 ~ ~ + - v c c g n d g a t e f b s e n s e c t r l ~ a z 4 3 1 a p 3 1 2 5 h a l 2 t 1 r 1 3 c 7 c 6 c 8 r 1 4 r 1 5 r 1 6 r 1 7 r 1 8 c 9 c 1 0 r 1 2 r 1 1 r 1 0 r 9 c 5 r 6 r 1 9 c 4 r 5 r 4 c 2 c 1 v r 1 u 1 n t c r 2 r 3 f 1 r 7 c 3 c 1 1 n t c r 8
AP3125HA/hb document number: ds37169 rev . 3 - 2 3 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product pin description s pin number p in name function AP3125HA ap3125h b 1 1 gnd signal ground. current return for driver and control circuits 2 2 fb feedback. directly connected to the opto - coupler 3 C ctrl latch trigger if this pin voltage drops below a threshold or over another threshold, leave ctrl pin open if this function is not needed. connecting a ntc thermistor to gnd can achieve otp protection C 3 bno b rownout p rotection pin, connect a resistor divider to set the brownout level 4 4 sense current sense 5 5 vcc supply voltage of driver and control circuits 6 6 gate gate driver output functional block diagram g n d g a t e 2 5 0 n s l e b d r i v e r 1 3 v o s c w i t h f r e q u e n c y j i t t e r 0 . 9 5 v v c c _ o v p o l p v c c 3 2 v 2 8 v v c c _ o v p c t r l ( a p 3 1 2 5 h a ) u v l o 1 6 v 7 . 6 v 1 v a u t o r e c o v e r y p r o t e c t i o n a p 3 1 2 5 h a / h b 1 0 0 m a f b r 2 r p w m 0 . 3 v 1 . 3 v l a t c h - o f f p r o t e c t i o n 7 0 m s d e b o u n c e o l p f o c p 3 v 4 . 5 v 0 . 6 v 1 0 k c t r l _ h c t r l _ l o c p s s s s v d d l i n e c o m p e n s a t i o n s o f t s t a r t 1 . 8 0 v f o c p q d c l k r b d f f o t p v c c v d d o t p c t r l _ h c t r l _ l v d d i n t e r n a l b i a s + 1 5 0 c o / + 1 2 5 o c s e n s e 1 2 5 4 3 6 l o v p b r o w n o u t 0 . 9 5 v 4 . 2 v 5 . 5 v l i n e _ o v p b r o w n o u t 0 . 9 v 5 0 m s d e b o u n c e 3 b n o ( a p 3 1 2 5 h b )
AP3125HA/hb document number: ds37169 rev . 3 - 2 4 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product absolute maximum ratings ( note 4 ) symbol parameter rating unit v cc power supply voltage 30 v i o gate output current 350 ma v fb , v sense , v ctrl input voltage to fb, sense, ctrl - 0.3 to 7 v ja thermal resistance (junction to ambient) 250 c /w p d power dissipation at t a < + 25 c 500 mw t j operating junction temperature - 40 to + 150 c t stg storage temperature range + 150 c C esd ( human body model) 3 000 v C esd ( machine model) 300 v note 4 : stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. these are stres s ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended o perating conditions is not implied. exposure to absolute maximum ratings for extended periods may affect device reliability. recommended operating conditions symbol parameter min max unit v cc supply voltage 10 2 5 v
AP3125HA/hb document number: ds37169 rev . 3 - 2 5 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product electrical characteristics (@ t a = + 25c, v cc = 16v, unless otherwise specified .) symbol parameter conditions min typ max unit supply voltage (vcc pin) i startup startup current C C 1 10 a i cc operating supply current v fb =0v, c l =1nf 0.5 0.7 1 ma v fb =3v, c l =0nf 0.6 1.2 2.0 C u vlo (on) C 14.5 15.8 16.5 v C v cc maintain C 8.6 9.1 9.6 v C u vlo (off) C 7.1 7.6 8.1 v C v cc ovp C 27 28.5 30 v C v cc clamp i cc =5ma 31 34 C v pwm section/oscillator section C maximum duty cycle C 70 75 80 % C oscillation frequency C 92 100 108 khz C green mode frequency C 20 C 30 khz ? C frequency temperature stability - 2 0 c to + 125 c (note 5 ) C C 5 % ? C frequency voltage stability v cc =12v to 30v C C 3 % ? C frequency dithering C 4 6 8 % ? current sense section (sense pin) v c s maximum sense voltage v fb = 4.5 v 0.9 0.95 1 v C focp voltage C 1.5 1.7 1.9 v C leb time of sense C 150 250 350 ns C delay to output (note 5 ) C C 100 C ns C soft - start time C 3 5 8 ms feedback input section (fb pin) C the ratio of input voltage to current sense voltage C 2.5 3 3.5 v /v C input impedance C 12 1 5 1 8 k C source current v fb =0v - 0.2 - 0.27 - 0.34 ma C green mode threshold C C 2.3 C v C input voltage for zero duty C 1.3 1.55 1.8 v output section (gate pin) C output low level i o =20ma, v cc =12v C C 1 v C output high level i o =20ma, v cc =12v 8 C C v C output clamping voltage C 11 13 15 v C rising time (note 5 ) c l = 1nf, v cc =13v C 150 250 ns C falling time (note 5 ) c l =1nf, v cc =13v C 50 100 ns
AP3125HA/hb document number: ds37169 rev . 3 - 2 6 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product electrical characteristics (cont.) (@ t a = + 25c, v cc = 16v, unless otherwise specified .) symbol parameter conditions min typ max unit protection section (ctrl pin , for AP3125HA ) C source current C 93 100 107 a C internal reference voltage C C 1.9 C v C low threshold trigger for latch C 0.9 7 1 .01 1.0 4 v C high threshold trigger for latch C 2.85 3 3.15 v C pull - up current (note 6 ) C C C 2 ma brownout section (bno pin , for ap3125hb ) C b rown - in voltage C 0.93 5 0.95 5 0.97 5 v C b rownout voltage C 0.8 75 0. 895 0.9 15 v C clamp ing voltage i clamp =1ma C 5.5 C v C line ovp C 4.1 4.2 4.3 v delay time section C delay of short circuit protection C C 70 C ms C delay of hiccup protection vcc ovp C 5 C c ycles i nternal otp section C otp enter C C + 150 C c C otp exit C C + 125 C c note s: 5 . guaranteed by design. 6 . the sourcing current of ctr l pin must be limited below 5ma . otherwise it may cause permanent damage to the device.
AP3125HA/hb document number: ds37169 rev . 3 - 2 7 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product performance characteristics start up voltage v s. ambient temperature shutdown voltage vs. ambient temperature start up current v s. ambient temperature operating current v s . ambient temperature ctrl utilization for latch ovp and otp ovp ot p c t r l v c c n t c -40 -20 0 20 40 60 80 100 120 140 6.5 7.0 7.5 8.0 8.5 9.0 shutdown voltage (v) ambient temperature ( o c) v c c c t r l n t c -40 -20 0 20 40 60 80 100 120 140 13 14 15 16 17 18 startup voltage (v) ambient temperature ( o c) -40 -20 0 20 40 60 80 100 120 140 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 startup current ( m a) ambient temperature ( o c) c t r l v c c n t c -40 -20 0 20 40 60 80 100 120 140 0.5 0.6 0.7 0.8 0.9 v fb =3v, c l =0 operating current (ma) ambient tempture ( o c)
AP3125HA/hb document number: ds37169 rev . 3 - 2 8 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product bno utilization for brownout operation description the ap 3125 h a/ hb is specifically designed for off - line ac - dc power supply used in lcd monitor, notebook adapter and battery charger applications. it offers a cost effective solution with a versatile protection function. start - up current and uvlo the start - up current of a p 3125 h a/ hb is optimized to realize ultra low current ( 1 m a typical) so that vcc capacitor can be charged more quickly. the direct benefit of low start - up current is the availability of using large start - up resistor, which minimizes the resistor power loss for high voltage ac input. an uvlo comparator is included in ap 3125 h a/ hb to detect the voltage on vcc pin. it ensures that ap 3125 h a/ hb can draw adequate energy from hold - up capacitor during power - on. the turn - on threshold is 1 6 v and the turn - off threshold is 7 .6v. current sense comparator and pwm latch the AP3125HA/hb operate s as a current mode controller, the output switch conduction is initiated by every oscillator cycle and is terminated when the peak inductor current reaches the threshold level established by the fb pin. the inductor current signal is co nverted to a voltage signal by inserting a reference sense resistor r s . the inductor current under normal operating conditions is controlled by the voltage at fb pin. the relation between peak inductor current (i pk ) and v fb is: moreover, focp with 1.8v t hreshold is only about 100 n s delay, which can avoid some catastrophic damages such as secondary rectifier short test. few drive cycles can alleviate the destruction range and get better protection. leading - edge blanking a narrow spike on the leading edge of the current waveform can usually be observed when the power mosfet is turned on. a 250ns leading - edge blank is built - in to prevent the false - triggering caused by the turn - on spike. during this period, the current limit comparator is disabled and the gate driver can not be switched off. at the time of turning off the mosfet, a negative undershoot (maybe larger than - 0.3v) can occur on the sense pin. so it is strongly recommended to add a small rc filter or at least con nect a resistor r on this pin to protect the ic (shown as figure 1 ). figure 1 built - in slope compensation it is well known that a continuous current mode smps may become unstable when the duty cycle exceeds 50%. the built - in slope compensation can improve the stability, so there is no need for design engineer to spend much time on that. fb pin and short circuit protection this pin is normally connected to the opto - coupler and always paralleled w ith a capacitor for loop compen sation. when the voltage at this pin is s fb pk r v i 3 / ) 8 . 0 ( ? ? f b s e n s e g a t e g n d c t r l ( b n o ) 6 1 3 4 a p 3 1 2 5 h a / h b v c c 5 2 l a r g e u n d e r s h o o t ( m o r e t h a n - 0 . 3 v ) m a y d a m a g e t h e s e n s e p i n r c n e c e s s a r y b n o c b u c k
AP3125HA/hb document number: ds37169 rev . 3 - 2 9 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product operation description (cont.) greater than 4. 5 v and lasts for about 70 ms, the ic will enter the protection mode. for AP3125HA/hb , the system will enter hiccup mode to wait the v cc decreasing to low uvlo level, then the ic will try to restart until the failure removed. and when this voltage is less than 1 .55v, the ic will stop the drive pulse immediately. therefore, this feature can be used for short circuit protection, which makes the system immune from damage. normally, output short makes the v fb value to the maximum because the opto - coupler is cut off. v cc maintain mode during light load or step load, v fb will drop and be lower than 1.55v, thus the pwm drive signal will be stopped, and there is no more new energy transfer r ed due to no switching. therefore, the ic supply voltage may reduce to the shutdown threshold voltage and system may enter the unexpected restart mode. to avoid this, the AP3125HA/hb hold a so - called v cc maintain mode which can supply energy to vcc. when v cc decreases to a setting threshold, the v cc maintain comparator will output some drive signal to make the system switch and provide a proper energy to vcc pin. the v cc maintain function will cooperate with the pwm and burst mode loop which can make the output voltage vari ation be within the regulation. this mode is very useful for reducing startup resistor loss and achie v ing a better standby performance with a low value vcc capacitor. th e v cc is not easy to touch the shutdown threshold during the startup process and step load. this will also si mplify the system design. the minimum vcc voltage is suggested to be designed a l ittle higher than v cc maintain threshold thus can achieve the best balance between the standby and step load performance . system protection and pin fault protection the AP3125HA/hb provides versatile system and pin fault protections. the ocp comparator realizes the cycle - by - cycle current limiting (ocp). in universal input line voltage, the ic realizes the constant over load protection (olp). vcc over voltage protection can be app lied as the primary ovp or opt o - coupler broken protection. the AP3125HA/hb also has pin fault connection protection including floating and short connection. the floating pin protection includ e s the sense, fb, etc. the short pin protection includes the ctrl pin short protection. when th ese pins are floated or ctrl pin is shorted to ground, pwm switching will be disabled, thus protecting the power system. e xternal otp protection function the ctrl pin of AP3125HA has two kinds of modes to trigger the latch protection: high level trigger (auto - recovery mode) and low level trigger (latch mode) . the low threshold is 1 v and high threshold voltage is 3 v. once the latch protection is tri ggered, the ic will disable the output signal, and the bulk capacitor provides the energy to ic through the startup resistor to ensure the ic disable the output. this mode will be not released until the ac input is shut off. so, the de - latch time is mainly depending on the hv startup bulk capacitor value. therefore, if the system want s a short de - latch time, it is better for the startup resistor take power from the point before the rectifier bridge as illustrated in f igure 2 . brownout protection function to avoid potential high current stress at low line voltage, ap3125 h b introduces reliable brownout protection. ac line voltage information is sampled through a voltage divider net - work, adjust ing the divider ratio to achieve expected brownout protection voltage. a typical 0.1n f capacitor is strongly recommended to parallel with bno pin to bypass any accidental spike in ac line for prevent ing false trigger. when the voltage across bno pin is higher than 0.95v and v cc reaches uvlo/on, the g ate pin will output drive signal s . if the bno voltage falls below 0.9v and lasts for 50 m s, the g ate pin will turn off and the system will enter hiccup mode until the line voltage rises over its brown - in voltage again. i nternal otp protection function t he AP3125HA/hb integrates an internal temperature sensor. i t has a trigger window of entering otp mode at + 15 0 c and exiting at + 125c . the internal otp protection mode is auto - recovery mode. figure 2 v c c g n d f b c t r l a p 3 1 2 5 h a s e n s e a c m a i n s ( 9 0 v t o 2 6 5 v ) c b u s g a t e 1 2 3 4 5 6
AP3125HA/hb document number: ds37169 rev . 3 - 2 10 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product ordering information diodes ics pb - free products with "g1" suffix in the part number, are rohs compliant and green . package part number marking id packing sot26 ap 3125h aktr - g1 g np 3 000/ tape & reel ap 3125hb ktr - g1 g nq 3 000/ tape & reel *product version classification ( with different protection functions ) product version frequency vovp olp & socp ctrl (low) ctrl (high) bno lovp ap 3125h a 100 khz auto - recoverable auto - recoverable latch auto - recoverable C C ap 3125hb 100 khz auto - recoverable auto - recoverable C C auto - recoverable latch mark ing information ( top view) : logo xxx: marking id ( see o rdering information ) a p 3 1 2 5 x x x x x - x x p a c k i n g p r o d u c t v e r s i o n * t r : t a p e & r e e l g 1 : g r e e n p r o d u c t n a m e r o h s / g r e e n p a c k a g e k : s o t 2 6 h a : a p 3 1 2 5 h a h b : a p 3 1 2 5 h b
AP3125HA/hb document number: ds37169 rev . 3 - 2 11 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product package outline dimensions (all d imensions in mm ( inch ) . ) (1) package t ype: sot26 2 . 8 2 0 ( 0 . 1 1 1 ) 3 . 1 0 0 ( 0 . 1 2 2 ) 2 . 6 5 0 ( 0 . 1 0 4 ) 3 . 0 0 0 ( 0 . 1 1 8 ) 1 . 5 0 0 ( 0 . 0 5 9 ) 1 . 7 0 0 ( 0 . 0 6 7 ) 0 . 9 5 0 ( 0 . 0 3 7 ) t y p 1 . 8 0 0 ( 0 . 0 7 1 ) 2 . 0 0 0 ( 0 . 0 7 9 ) 0 . 3 0 0 ( 0 . 0 1 2 ) 0 . 5 0 0 ( 0 . 0 2 0 ) 0 . 7 0 0 ( 0 . 0 2 8 ) r e f 0 . 1 0 0 ( 0 . 0 0 4 ) 0 . 2 0 0 ( 0 . 0 0 8 ) 0 8 0 . 2 0 0 ( 0 . 0 0 8 ) 0 . 3 0 0 ( 0 . 0 1 2 ) 0 . 6 0 0 ( 0 . 0 2 4 ) 0 . 0 0 0 ( 0 . 0 0 0 ) 0 . 1 5 0 ( 0 . 0 0 6 ) 0 . 9 0 0 ( 0 . 0 3 5 ) 1 . 3 0 0 ( 0 . 0 5 1 ) 1 . 4 5 0 ( 0 . 0 5 7 ) m a x 1 2 3 4 5 6 p i n 1 m a r k
AP3125HA/hb document number: ds37169 rev . 3 - 2 12 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product suggested pad layout (1) package t ype: sot26 dimensions z (mm)/(inch) g (mm)/(inch) x (mm)/(inch) y (mm)/(inch) e (mm)/(inch) value 3.600/0.142 1.600/0.063 0.700/0.028 1.000/0.039 0.950/0.037 e e g z y x
AP3125HA/hb document number: ds37169 rev . 3 - 2 13 of 13 www.diodes.com july 2014 ? diodes incorporated ap31 25 ha/hb a product line of diodes incorporated new product important notice diodes incorporated makes no warranty of any kind, express or implied, with regards to this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose (and their equivalents under the laws of any jurisdiction). diodes incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. diodes incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does diodes incorporated convey any license unde r its patent or trademark rights, nor the rights of others. any customer or user of t his document or products described herein in such applications shall assume all risks of such use and will agree to hold diodes incorporated and all the companies whose products are represented on diod es incorporated website, harmless against all damages. diodes incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthor ized sales channel. should customers purchase or use diodes incorporated products for any unintended or unauthorized application, customers shall indemnify and hold diodes incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising ou t of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. products described herein may be covered by one or more united states, international or foreign patents pending. product nam es and markings noted herein may also be covered by one or more united states, internatio nal or foreign trademarks. this document is written in english but may be translated into multiple languages for reference. only the english version of this document is the final and determinative format released by diodes incorporated. life support di odes incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the chief executive officer of diodes incorporated. as used herein: a. life support devi ces or systems are devices or systems which: 1. are intended to implant into the body, or 2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided i n the labeling can be reasonably expected to result in significant injury to the user. b. a critical component is any component in a life support device or system whose failure to perform can be reasonably expe cted to cause the failure of the life support device or to affect i ts safety or effectiveness. customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support d evices or systems, and acknowledge and agree that they are solely responsible for all legal, regulator y and safety - related requirements concerning their products and any use of diodes incorporated products in such safety - critical, life support devices or systems, notwithstanding any devices - or systems - related information or support that may be provided by diodes incorporated. further, customers must fully indemnify diodes incorporated and its representatives against any damages arising out of the use of diodes incorporated products in such safety - critical, life support devices or systems. copyright ? 201 4 , diodes incorporated www.diodes.com

▲Up To Search▲

Price & Availability of AP3125HA

	To Download AP3125HA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .